Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
Were you on the lookout for information about A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't exactly brain surgery, however it does need solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bathtub with a new one is also a reasonably challenging job. If the old tub is readily available, the job can relocate speedily; if you have to open up a wall to get rid of the old bathtub as well as position the new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have certified on your own for the task as well as fit trying it. Rather than employing a specialist to take over a halfway-completed task, it is better to consider utilizing one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This post will help you install a brand-new bathtub in your bathroom if you have actually currently gotten a brand-new bathtub and also don't need to change the plan of your previous water system pipelines.
Your tools and product list ought to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the water supply. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be rather troublesome due to the limited gain access to that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the staying water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location between the tap as well as the sink. Secure the tap in place with the maker provided backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Making use of the two wood boards under its feet, place the bathtub in the needed setting. The wood boards are handy in evenly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bathtub up until the spirit level reviews degree.
To mount faucets, fit the bottom of the furthest versatile tap connector to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the supply of water as well as check all joints and new pipework for leakages as well as tighten them if required. Fill up the tub as well as likewise check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub should wait up until the bath tub has actually been made use of at the very least when as this will settle it into its last placement.
Preparing for the Installation
Firstly, the supporting framework supplied with the bathroom should be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to stop pressure on the bath tub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in issues with dampness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to enable the motion experienced when the bathtub is in usage. The sealer can crack relatively early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly available on the market. It is a good idea to fit the ceramic tiles making use of water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted reader on How to Install a Bathtub Yourself, I thought sharing that excerpt was worth the trouble. Loved our review? Please share it. Help another person discover it. Bless you for your time. Don't hesitate to come visit our site back soon.
This Site
Report this page